Great-plains 3S-4000F Predelivery Manual Bedienungsanleitung

Manufacturing, Inc.Cover illustration may show optional equipment not supplied with standard unit.!Read the operator’s manual entirely. When you see t

3S-4000195-242Q9/12/20098Installing Press Wheels1. Remove 1/2 x 3-3/4 inch flange bolt (1) andflange lock nut (2) from each opener body.2. Leave pivot b

9/12/2009195-242Q9AssemblyInstalling WalkboardsBolts for walkboards are shipped in a bag in one ofthe drill boxes.Bolt walkboards (1) to box support c

3S-4000195-242Q9/12/200910Installing Reflectors and DecalsDecals are shipped in a bag in one of the drillboxes.To install new reflectors and decals:• C

9/12/2009195-242Q11AssemblyAcremeterAssemble acremeter (1) to end of main drive shafton the center section as shown.189221Post Assembly Checklist1. Ch

3S-4000195-242Q9/12/200912Hitching Tractor to Drill!DANGERYou may be severely injured or killed by being crushedbetween the tractor and drill. Do not

9/12/2009195-242Q13Setup3. Bolt drill hitch onto drill tongue to match yourtractor-drawbar height. You can turn the hitchover for a total of six diffe

3S-4000195-242Q9/12/200914Hydraulic Hose Hookup!WARNINGEscaping fluid under pressure can penetrate the skincausing serious injury. Avoid the hazard by

9/12/2009195-242Q15SetupBleeding HydraulicsTo function properly, the hydraulics must be free ofair. If hydraulics have not been bled, they will op-era

3S-4000195-242Q9/12/2009166. Slowly supply oil to top side of pressure-con-trol valves until oil begins to appear at a loos-ened hose fitting. As oil b

9/12/2009195-242Q17SetupBleeding Fold Hydraulics.1. Check hydraulic fluid level in tractor reservoirand fill to proper level. Add fluid to system asneede

Table of Contents© Copyright 2001, 2009 All rights ReservedGreat Plains Manufacturing, Inc. provides this publication “as is” without warranty of any

3S-4000195-242Q9/12/200918Bleeding Transport Lift Hydraulics.1. Check hydraulic fluid level in tractor reservoirand fill to proper level. Add fluid to sy

9/12/2009195-242Q19SetupBleeding Marker Hydraulics!CAUTIONYou may be injured if hit by a folding or unfoldingmarker. Markers may fall quickly and unex

3S-4000195-242Q9/12/200920Folding!WARNINGCrushing hazard – Bystanders could be crushed be-tween the folding drill boxes and the drill tongue. Toavoid

9/12/2009195-242Q21SetupUnfolding1. Park tractor and drill on level ground with trac-tor transmission in park. Be aware of clear-ance needed to unfold

3S-4000195-242Q9/12/200922Leveling the DrillCenter Box Frame Leveling1. Park the drill on a clean level surface.2. Raise the openers and lock them up.

9/12/2009195-242Q23SetupFrame AdjustmentsToolbar Height AdjustmentToolbar height is factory set and normally will notrequire adjustment. If the toolba

3S-4000195-242Q9/12/200924Wing Box Alignment1. Place a block ahead of the wing gaugewheels.2. Pull forward against blocks to rock wingframes back. Pul

9/12/2009195-242Q25SetupAlign Transfer Drive ShaftAfter wing boxes are properly aligned, the transferdrive shaft must be aligned so the pair of break-

3S-4000195-242Q9/12/200926Refer to Figure 12.3. To align the clutch jaws from front to rear,loosen the two 1/2 inch carriage bolts (3) andslide breaka

9/12/2009195-242Q27SetupInstall Final AccessoriesAcremeter InstallationRefer to Figure 14.The acremeter is supplied from the factory in a sepa-rate c

9/12/2009195-242Q1Important Safety InformationImportant Safety Information!For your safety, thoroughly read Important Safe-ty Information in the opera

3S-4000195-242Q9/12/200928AppendixTorque Values Chart for Common Bolt Sizesin-tpi1N · m2ft-lb3N · m ft-lb N · m ft-lb mm x pitch4N · m ft-lb N · m ft-

9/12/2009195-242Q29AppendixHydraulic SchematicsTire Inflation ChartTire Size InflationPSITire Size InflationPSI7.50 x 20" 4-Ply Drill Rib 28 11L

3S-4000195-242Q9/12/200930Opener Hydraulics for Open Center SystemsHydraulic Schematics20003

9/12/2009195-242Q31AppendixTransport Fold Hydraulics15602Transport Lift HydraulicsHydraulic Schematics18931

3S-4000195-242Q9/12/20093215605Kit for Tractors with Two OutletsHydraulic SchematicsDual Marker HydraulicsSingle Marker Hydraulics

Great Plains Manufacturing, Inc.Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA

3S-4000195-242Q9/12/20092Avoid High Pressure FluidsEscaping fluid under pressure can penetrate theskin, causing serious injury.▲ Avoid the hazard by re

9/12/2009195-242Q3Important Safety InformationUse A Safety Chain▲ Use a safety chain to help control drill shouldit separate from tractor drawbar.▲ Us

3S-4000195-242Q9/12/20094Great Plains Manufacturing wants you to be satis-fied with any new machine delivered by the GreatPlains Trucking network. To e

9/12/2009195-242Q5IntroductionUsing This ManualThis manual was written to help you assembleand prepare the new machine for the customer.The manual inc

3S-4000195-242Q9/12/20096The following headings are step-by-step instruc-tions for assembling the 4000-3S drill. Begin with“Tools Required” and “Pre-A

9/12/2009195-242Q7AssemblyInstalling Middle Box on Frame1. With forklift chains secured around lifting baron back of center section box, lift center s