Great-plains 3S-3000 Installation Instructions Bedienungsanleitung PDF herunterladen

Great Plains Mfg., Inc.

General Information 1

2- and 3-Section Folding Drill

Open Center Hydraulic Kit

Used with:

• 2S-2600, 2S-2600HD

• 3S-3000, 3S-3000HD

• 3S-4000, 3S-4000HD

General Information

These instructions explain how to install an Open Center

Hydraulic Kit, required for operating any of these drills

with tractors having open-center hydraulics, or ﬁxed-dis-

placement hydraulic pumps.

These instructions apply to an installation of

Note: Do not install this kit on a Point Row-equipped

drill. These two options use the same mounting

locations, cannot be co-located, and this kit does

not upgrade Point Row hydraulics to open center

operation.

Each kit converts an entire drill.

Tools Required

• current Operator and Parts manuals (see page 21)

• basic hand tools,

• liquid (not tape) pipe thread sealant,

• fresh hydraulic ﬂuid, and;

• suitable tractor or hydraulic source for charging sys-

tem and making initial adjustments.

Table of Contents

Installation steps vary for 2- and 3-section drills, and vary

for older vs. newer 2-section drills.

Before You Start ...........................................................2

Pre-Assembly Preparation............................................2

3S-3000 and 3S-4000 Installation ................................3

2S-2600 DD1161- Installation ......................................9

2S-2600HD and 2S-2600 DD1162+ Installation ........15

Closeout .....................................................................21

Setup ..........................................................................21

Appendix ....................................................................21

Torque Values ......................................................21

Current Manuals ..................................................21

New Parts ............................................................22

Existing Parts Affected.........................................23

Abbreviations .......................................................23

Notations and Conventions

“Left” and “Right” are facing in the

direction of machine travel. An orienta-

tion rose in the line art illustrations

shows the directions of Up, Back, Left,

Down, Front and Right.

Call-Outs

Kit Kit Description

194-143A

2600 3000 4000 OPEN-CTR HYDKIT

When you see this symbol, the subsequent instructions

and warnings are serious - follow without exception.

Your life and the lives of others depend on it!

FigureSpacer

Figure 1: Parts

Kit (Black) / Existing (Gray)

27485

Single-digit callouts identify components in

the currently referenced Figure or Figures.

These numbers may be reused for different

items from page to page.

Two-digit callouts in the range 11 to 24 refer-

ence new parts from the new parts lists

beginning on page 22.

Two-digit callouts in the range 51 to 65 refer-

ence affected existing parts from the table on

page 23. The descriptions match those in

your Parts Manual. The narrative and table

indicate any re-use of the parts.

1 9

11 24

51 65

1 2 3 4 5 6 ... 23 24

Inhaltsverzeichnis

Seite 1 - General Information

Seite 2 - Pre-Assembly Preparation

Great Plains Mfg., Inc.10 Open Center Hydraulic Kit194-149M 09/05/20122S DD1161- Check Valve InstallationRefer to Figure 1153. Select two new: 811-636

Seite 3 - 3S Control Valve Disassembly

Great Plains Mfg., Inc.2S-2600 DD1161- Installation 1109/05/2012 194-149M2S DD1161- Shuttle Valve AssemblyRefer to Figure 1262. Select one new: 810-34

Seite 4

Great Plains Mfg., Inc.12 Open Center Hydraulic Kit194-149M 09/05/20122S DD1161- Shuttle Valve InstallationRefer to Figure 1474. Select two sets of: 8

Seite 5

Great Plains Mfg., Inc.2S-2600 DD1161- Installation 1309/05/2012 194-149MFigureSpacerCENTERWINGBASE END, CENTER OPENERSBASE END, WING OPENERS120060003

Seite 6

Great Plains Mfg., Inc.14 Open Center Hydraulic Kit194-149M 09/05/20122S-2600 DD1161- Hydraulic SchematicFigureSpacerFigure 162S DD1161- Hydraulics187

Seite 7 - TO TRACTOR

Great Plains Mfg., Inc.2S-2600HD and 2S-2600 DD1162+ Installation 1509/05/2012 194-149M2S-2600HD and 2S-2600 DD1162+ InstallationStep 88 through step

Seite 8 - 194-149M 09/05/2012

Great Plains Mfg., Inc.16 Open Center Hydraulic Kit194-149M 09/05/20122S DD1162+ Check Valve InstallationRefer to Figure 1894. Select two new: 811-636

Seite 9 - 2S-2600 DD1161- Installation

Great Plains Mfg., Inc.2S-2600HD and 2S-2600 DD1162+ Installation 1709/05/2012 194-149M2S DD1162+ Shuttle Valve AssemblyRefer to Figure 19106. Select

Seite 10 - 85050146, and if

Great Plains Mfg., Inc.18 Open Center Hydraulic Kit194-149M 09/05/20122S DD1162+ Shuttle Valve InstallationRefer to Figure 21117. Select two sets of:

Seite 11 - 85005468, and the internal

Great Plains Mfg., Inc.2S-2600HD and 2S-2600 DD1162+ Installation 1909/05/2012 194-149MCENTERWINGBASE END, CENTER OPENERSBASE END, WING OPENERSROD END

Seite 12 - FigureSpacer

Great Plains Mfg., Inc.2 Open Center Hydraulic Kit194-149M 09/05/2012Before You StartReview the instruction for your drill, with the followingobjectiv

Seite 13 - Figure 15

Great Plains Mfg., Inc.20 Open Center Hydraulic Kit194-149M 09/05/20122S-2600 DD1162+ Hydraulic SchematicFigureSpacerFigure 232S DD1162+ Hydraulics229

Seite 14 - 2S DD1161- Hydraulics

Great Plains Mfg., Inc.Closeout 2109/05/2012 194-149MCloseout130. Connect the drill to the tractor or other hydraulicpower source.131. Perform the Ope

Seite 15

Great Plains Mfg., Inc.22 Open Center Hydraulic Kit194-149M 09/05/2012New PartsThis manual covers the installation of two different hold-down kits. Pa

Seite 16

Great Plains Mfg., Inc.Appendix 2309/05/2012 194-149MExisting Parts AffectedThe following existing parts are involved in the kit instal-lation.The Dis

Seite 17

Great Plains Mfg., Inc.24 Open Center Hydraulic Kit194-149M 09/05/2012Great Plains Manufacturing, Inc.Corporate Ofﬁce P.O. Box 5060Salina, Kansas 6740

Seite 18

Great Plains Mfg., Inc.3S-3000 and 3S-4000 Installation 309/05/2012 194-149M3S-3000 and 3S-4000 InstallationStep 11 through step 47 are for 3S-3000, 3

Seite 19 - Figure 22

Great Plains Mfg., Inc.4 Open Center Hydraulic Kit194-149M 09/05/20123S Check Valve InstallationRefer to Figure 416. Select two new: 811-636C AD 9/16M

Seite 20 - 2S DD1162+ Hydraulics

Great Plains Mfg., Inc.3S-3000 and 3S-4000 Installation 509/05/2012 194-149M3S Shuttle Valve AssemblyRefer to Figure 525. Select one new: 810-344C VAL

Seite 21 - Appendix

Great Plains Mfg., Inc.6 Open Center Hydraulic Kit194-149M 09/05/20123S Shuttle Valve InstallationRefer to Figure 735. Select two sets of: 802-551C HH

Seite 22 - New Parts

Great Plains Mfg., Inc.3S-3000 and 3S-4000 Installation 709/05/2012 194-149MFigureSpacerBASE END, CENTER OPENERSROD END, CENTER OPENERSBASE END, WING

Seite 23 - Abbreviations

Great Plains Mfg., Inc.8 Open Center Hydraulic Kit194-149M 09/05/20123S-3000 and 3S-4000 Hydraulic Schematic3S Drill VintagesDrills built in December

Seite 24 - Salina, Kansas 67402-5060 USA

Great Plains Mfg., Inc.2S-2600 DD1161- Installation 909/05/2012 194-149M2S-2600 DD1161- InstallationStep 48 through step 87 are for 2S-2600 drills ser

Kommentare zu diesen Handbüchern

Keine Kommentare

Great-plains 3S-3000 Installation Instructions Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Gartengeräte Great-plains 3S-3000 Installation Instructions herunter. Great Plains 3S-3000 Installation Instructions User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Gartengeräte Great-plains 3S-3000 Installation Instructions